|
Celcon® LW90
乙缩醛（POM）共聚物
Ticona
产品说明
Celcon® LW90 is a nominal 9 melt flow rate based material specifically formulated for high speed, low wear applications against metals. LW90 conforms to applicable FDA regulations governing food contact.
Chemical abbreviation according to ISO 1043-1: POM
总体
材料状态 • 已商用：当前有效
供货地区 • 北美洲 • 拉丁美洲 • 欧洲
• 非洲和中东 • 南美洲 • 亚太地区
性能特点 • 耐磨损性良好
机构评级 • FDA 食品接触, 未评级
RoHS 合规性 • 联系制造商
形式 • 颗粒料
加工方法 • 注射成型
多点数据 • Isothermal Stress vs. Strain (ISO 11403-1)
树脂ID (ISO 1043) • POM
物理性能 额定值单位制 测试方法
比重
-- 1.43g/cm³ ASTM D792
-- 1.41g/cm³ ISO 1183
熔流率 9.0g/10 min ASTM D1238
溶化体积流率（MVR） (190°C/2.16 kg) 8.00cm³/10min ISO 1133
收缩率
流动 2.2% ASTM D955
横向流动 1.8% ASTM D955
横向流量 1.5% ISO 294-4
流量 1.8% ISO 294-4
吸水率 ISO 62
饱和, 23°C 0.65%
平衡, 23°C, 50% RH 0.20%
机械性能 额定值单位制 测试方法
拉伸模量 2500MPa ISO 527-2/1A/1
抗张强度
屈服, 23°C 58.6MPa ASTM D638
屈服 64.0MPa ISO 527-2/1A/50
拉伸应变 (屈服) 9.0% ISO 527-2/1A/50
弯曲模量
23°C 2550MPa ASTM D790
23°C 2600MPa ISO 178
冲击性能 额定值单位制 测试方法
悬壁梁缺口冲击强度
23°C 64J/m ASTM D256
23°C 5.7kJ/m² ISO 180/1A
热性能 额定值单位制 测试方法
热变形温度
1.8 MPa, 未退火 97.2°C ASTM D648
1.8 MPa, 未退火 98.0°C ISO 75-2/A
维卡软化温度 161°C ISO 306/B50
线形膨胀系数 ISO 11359-2
流动 0.00011cm/cm/°C
横向 0.00012cm/cm/°C
1 / 2
Celcon® LW90 2012年10月14日
乙缩醛（POM）共聚物
Ticona
注射 额定值单位制
加工（熔体）温度 182 到 199°C
模具温度 82.0 到 93.0°C
注射说明
Standard reciprocating screw injection molding machines with a high compression screw (minimum 3:1 and preferably 4:1) and low back pressure (0.35 Mpa/50 PSI) are favored. Using a low compression screw (I.E. general purpose 2:1 compression ratio) can result in unmelted particles and poor melt homogeneity. Using a high back pressure to make up for a low compression ratio may lead to excessive shear heating and deterioration of the material.
Melt Temperature: Preferred range 182-199 C (360-390 F). Melt temperature should never exceed 230 C (450 F).
Mold Surface Temperature: Preferred range 82-93 C (180-200 F) especially with wall thickness less than 1.5 mm (0.060 in.). May require mold temperature as high as 120 C (250 F) to reproduce mold surface or to assure minimal molded in stress. Wall thickness greater than 3mm (1/8 in.) may use a cooler (65 C/150 F) mold surface temperature and wall thickness over 6mm (1/4 in.) may use a cold mold surface down to 25 C (80 F). In general, mold surface temperatures lower than 82 C (180 F) may hinder weld line formation and produce a hazy surface or a surface with flow lines, pits and other included defects that can hinder part performance.
备注
1 一般属性：这些不能被视为规格。
|
